True Wireless Stereo Earbud Charger Cradle

2022-05-28 15:46:41 By : Ms. Shally Liu

Getting TWS earbuds powered up quickly and in a small form factor.

During the last few years, Bluetooth-connected earbuds and headphones have gained significant market share over their wired ancestors. Especially, True Wireless Stereo (TWS) earbuds gained massive popularity with approximately 300M+ units sold in 2021. Technically, these earbuds resemble in-ear hearing aids, except that they offer advanced features such as wireless connectivity (Bluetooth) and in the higher-end devices voice detection and voice recognition. Like hearing aids, TWS earbuds are typically recharged in cradles containing a larger battery and offer USB and/or wireless charging. The similarity between these two systems was recently recognized by the FDA. See the “FDA Issues Landmark Proposal to Improve Access to Hearing Aid Technology for Millions of Americans” news release.

The fact that TWS earbuds and hearing aids rely on small integrated batteries to function leads most users to carry the matching cradle/charger case with them to recharge these on the move, requiring a small size combined with fast and flexible charging of both the audio devices and the charging cradle.

Typical features of state-of-the-art charging cases are wireless charging (WPC/Qi), USB-C and legacy USB charging, independent supply rails to each audio device to fast charging support, Power Line Communication (PLC) for communication between the cradle unit and each earbud, and sometimes Bluetooth Low Energy (LE) connectivity to track the charging case State-of-Charge (SoC) and its location.

Renesas’ solution to all these requirements and functions is shown in the “True Wireless Stereo (TWS) Earbud Charger Cradle” combination. The core functionality of charging the cradle’s battery, generating a boosted voltage to charge the TWS earbuds or hearing aids, and controlling each charging path separately is integrated in a single TWS cradle charging PMIC and battery management unit (DA9168).

Power to this PMIC is provided either through a USB connector or through a single-chip 5W wireless power receiver (P9222-R). The power-path is automatically selected by a 2:1 power mux (SLG591401C) which also contains overvoltage protection supporting USB-C ports and additional protection features.

To complement the base feature set of any TWS and hearing aid charger cradle, a small 16-bit MCU with native USB BC1.2 support is added for optimal legacy charging support from any available USB-type connector power source and to support advanced features such as power throttling to optimize each audio device’s charging speed, customized UI to display the charging state, the battery’s State-of-Charge (SoC), etc.

For advanced charging algorithms and to support e.g. direct charging of the connected earbuds, a UART compatible power line communication interface can be added by using a GreenPAK programmable mixed-signal matrix as a PLC modulator/demodulator interface unit connected to the power supply rails. This solution enables each earbud to control its charging voltage and current without requiring a significant size integrated power control, saving cost and especially precious PCB area and volume.

Adding a Bluetooth LE radio to the cradle enables functions such as device tracking, SoC information gathering without the earbuds being inserted, and Software Updates over the Air (SUotA).

Name* (Note: This name will be displayed publicly)

Email* (This will not be displayed publicly)

Suppliers are investing new 300mm capacity, but it’s probably not enough. And despite burgeoning 200mm demand, only Okmetic and new players in China are adding capacity.

Why UCIe is so important for heterogeneous integration.

Funding rolls in for photonics and batteries; 88 startups raise $1.3B.

Experts at the Table: Designing for context, and geopolitical impacts on a global supply chain.

Memory footprint, speed and density scaling are compounded by low-power constraints.

Interest in this particular ISA is expanding, but the growth of other open-source hardware is less certain.

Nanosheets are likeliest option throughout this decade, with CFETs and other exotic structures possible after that.

Hybrid bonding opens up whole new level of performance in packaging, but it’s not the only improvement.

Suppliers are investing new 300mm capacity, but it’s probably not enough. And despite burgeoning 200mm demand, only Okmetic and new players in China are adding capacity.

Why this is becoming a bigger issue, and what can be done to mitigate the effects.

From low resistance vias to buried power rails, it takes multiple strategies to usher in 2nm chips.

Manufacturing 3D structures will require atomic-level control of what’s removed and what stays on a wafer.

Disaggregation and the wind-down of Moore’s Law have changed everything.